JTAG-Booster for AMD élanSC400/élanSC410
3. Implementation Information
This chapter summarizes some information about the implementation of the
JTAG-Booster and describes some restrictions.
?
?
?
?
?
52
The JTAG-Booster uses the EXTEST function of the JTAG-Interface to
perform Flash programming.
Connect the signal BNDSCN_EN to Pin 4 of the connector for the JTAG-
Booster. Please note: The signal BNDSCN_EN of the AMD élanSC400 is
not 5V tolerant. If you power the JTAG-Booster with 5V (Pin 8 = +5V, Typ
227) there must be a protection circuit to protect the pin. On the FS FORTH-
SYSTEME module élan486 there is a level shifter for the BNDSCN_EN
signal and the standard 5V version of the JTAG-Booster can be directly
connected to the module.
The signal BNDSCN_EN switches the AMD élanSC400 complete to JTAG
test mode and normal operation is disabled. Therefor it is not possible to
observe CPU signals via JTAG interface while the CPU is running. (The
functions /SAMPLE and /SNAP are not available.)
ROMCS2 as a chip select to a memory device is not supported with an
separate option, because ROMCS2 can be mapped to any of the general
purpose chip select signals (GPIO_CSxx). If you want to use a memory
device connected to any of this GPIO_CSxx, you must set the default level of
this pin to Out,Lo in the file JTAGEL4.INI and must specify the option
/NOCS in the command line.
Most designs with the AMD élanSC400 need a data buffer to separate the
DRAM from the ISA-Bus and boot ROM. This buffer is controlled with the
signals GPIO_CS4 (DBUFOE#), GPIO_CS3 (DBUFRDH#) and GPIO_CS2
(DBUFRDL#). If your design doesn’t have this data buffer and you have
connected other components to GPIO_CS2..4 you must specify the option
/NOBUFF to switch off the generation of the control signals.
JTAGEL4c.doc
相关PDF资料
FS-929 JTAG-BOOSTER FOR SA-11X0 3.3V
FS-931 JTAG-BOOSTER FOR ELANSC520 3.3V
FS-935 JTAG-BOOSTER FOR IDT64145 3.3V
FS-940 JTAG-BOOSTER FOR ADSP-21XXX 5V
FSICEBASE BASE STATION FSICE FOR MCU MOD
FT24C02A-5LR-T IC EEPROM 2KBIT 1MHZ SOT23-5
FT24C16A-UMR-B IC EEPROM 16KBIT 1MHZ 8MSOP
FT24C256A-UMR-B IC EEPROM 256KBIT 1MHZ 8MSOP
相关代理商/技术参数
FS-929 功能描述:开发板和工具包 - ARM Forth JTAG Booster PC ARM SA-11x0 3.3V RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V
FS9309 WAF 制造商:Texas Instruments 功能描述:
FS-931 功能描述:开发板和工具包 - ARM Forth JTAG Booster Elan SC520 3.3V RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V
FS-932 功能描述:开发板和工具包 - ARM Forth JTAG Booster PC Siemens PCUD 3.3V RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V
FS-935 功能描述:开发板和工具包 - ARM Forth JTAG Booster PC IDT64145 3.3V RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V
FS-940 功能描述:开发板和工具包 - ARM JTAG Booster PC ADSP-21xxx 5V RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V
FS-945 功能描述:开发板和工具包 - ARM JTAG Booster PC Elan SC400 3.3V RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V
FS94NS 制造商:BOTHHAND 制造商全称:Bothhand USA, LP. 功能描述:SMD, 14 PIN, 10 BASE-T FILTER FOR PCMCIA APPLICATIONS